Peerless FPE42F-S Manual

Installation and Assembly:Peerless Environmental Enclosure for 42" Flat Panel ScreensModel: FPE42F-S, FPE42FH-S, FPE42F-BISSUED: 07-16-10 SHEET

10 of 18ISSUED: 07-16-10 SHEET #: 061-9050-4 03-04-11Installing Adapter BracketsTo prevent scratching the screen, set a cloth on a fl at, level surf

11 of 18ISSUED: 07-16-10 SHEET #: 061-9050-4 03-04-11Begin with the shortest length screw, hand thread through multi-washer and adapter bracket int

12 of 18ISSUED: 07-16-10 SHEET #: 061-9050-4 03-04-11Hook adapter brackets (B) onto wall plate (J) then slowly swing screen in as shown in fi gure 7

13 of 18ISSUED: 07-16-10 SHEET #: 061-9050-4 03-04-11Firmly grasp top and bottom of screen. Lift up and push the bottom of the rear supports back u

14 of 18ISSUED: 07-16-10 SHEET #: 061-9050-4 03-04-11NOTE: The installed display should allow a 1/2" air gap between the front of the screen a

15 of 18ISSUED: 07-16-10 SHEET #: 061-9050-4 03-04-11Refer to screen manufacturers' requirements for optimal environment temperature. If scree

16 of 18ISSUED: 07-16-10 SHEET #: 061-9050-4 03-04-11Locking Environmental EnclosureGently lower bay door. Using key (G) rotate door locks clockwis

17 of 18ISSUED: 07-16-10 SHEET #: 061-9050-4 03-04-11Filterfan replacement fi ltermats are sold separately at www.fi lterfanusa.com, for Filterfan mo

18 of 18ISSUED: 07-16-10 SHEET #: 061-9050-4 03-04-11© 2008 Peerless Industries, Inc. Peerless Industries, Inc. establishes a warranty period of fi

2 of 18ISSUED: 07-16-10 SHEET #: 061-9050-4 03-04-11NOTE: Read entire instruction sheet before you start installation and assembly. Table of Conten

3 of 18ISSUED: 07-16-10 SHEET #: 061-9050-4 03-04-11CEGHIFABBefore you begin, make sure all parts shown are included with your product.Parts may ap

4 of 18ISSUED: 07-16-10 SHEET #: 061-9050-4 03-04-11Adapter Bracket FastenersM4 x 12 mm (4)(504-9013)M6 x 25 mm (4)(520-1208)M4 x 25 mm (4)(504-101

5 of 18ISSUED: 07-16-10 SHEET #: 061-9050-4 03-04-11Optional Removal of Bay Door1Bay door may be removed for ease of installation to mounting surfa

6 of 18ISSUED: 07-16-10 SHEET #: 061-9050-4 03-04-11Cables may be routed through top, bottom, or rear of main enclosure assembly. An additional ava

7 of 18ISSUED: 07-16-10 SHEET #: 061-9050-4 03-04-11Installation to Wood Stud WallNOTE: This step is for mounting enclosure assembly (A) fl ush agai

8 of 18ISSUED: 07-16-10 SHEET #: 061-9050-4 03-04-11Wall Plate InstallationReinstall rear supports into carriage supports. NOTE: Be sure "UP&q

9 of 18ISSUED: 07-16-10 SHEET #: 061-9050-4 03-04-11Reinstalling Bay DoorIf bay door was removed in step 1, lower bay door onto enclosure assembly